Page 19 - Filter Cartridges Product Catalogue

PERFORMANCE SPECIFICATIONS

• Hot DI Water: Filter cartridge will withstand temperatures of 185°F (85°C) for up to 30 consecutive minutes
• Cleaning/Sanitization: Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with
pH range from 1–14 Consult factory for specific compatibility information
• Steam/Autoclave: Cartridges may be steamed or autoclaved for at least 50 thirty-minute cycles @ 275°F (135°C)
FILTR ATION | SEPAR ATION | PURIFICATION
ZTEC B NOMENCLATURE INFORMATION
ZTEC B Series Filter Retention Rating Nominal Length End Gasket
™
Type
or O-Ring
Configuration
(microns)
(inches)
Filter Cartridges ZTEC B 0.2 –5 * –20 P Double Open End B Buna-N
Series
226/Flat Single Open End
EPDM
E
P2
–9.75
0.45
–30
0.65 –10 –40 P3 222/Flat Single Open End S Silicone
Pleated Polyethersulfone (PES) Membrane P7 226/Fin Single Open End T Teflon encap
for Bioburden Reduction in Beverages P8 222/Fin Single Open End Viton (O-Rings
only)
and Biopharmaceuticals AM Single Open End, Internal O-Ring T Teflon (gaskets)
Example: ZTEC B 0.2–20P2E NPC Double Open End, Internal O-Ring V Viton
ZTEC B Bioburden Reduction grade membrane cartridges provide high-
Product Specifications ly consistent performance for bioburden reduction and particle removal ZTEC B 0 2 –20 P2 E
Media: Asymmetric across a wide range of beverage, pharmaceutical and biological fluids The *Available only for DOE (P) configuration
Polyethersulfone Membrane naturally hydrophilic PES membrane filters provide exceptional flow rates,
Inner core, end caps, cage: Polypropylene long on-stream life, broad chemical compatibility and have no added sur- ZTEC B FLOW RATE INTEGRITY TEST SPECIFICATIONS
Support layers: Spunbonded factants to contribute to extractables The cartridges are integrity testable Typical Flow Rate Clean Water at Ambient Temperature Minimum Bubble Point values and maximum
Polypropylene and steamable to assure reliable service in critical applications (per 10" cartridge) Diffusive Air Flow (per 10-inch cartridge) values
Gaskets/O-Rings: FEATURES & BENEFITS BAR PSI for ZTEC B filters wet with water:
Buna-N, EPDM, Silicone, Teflon 0 28 4 Pore Size Bubble Point Diffusive Air Flow
Encapsulated Viton (O-Rings only), • Manufactured in an ISO Class 7 Cleanroom Environment
Teflon (gaskets), Viton • 100% flushed with ultrapure DI water and integrity tested 0 21 3 0 2 µm 0 2 μm ≥ 38 psig ≤ 35 cc/min @
Micron ratings: 0 2, 0 45, 0 65 µm (2 8 bar) 30 psig (2 0 bar)
• Repeatably steamable/sanitizable Differential Pressure 0 14 2
Dimensions • High retentions up to 10 /cm challenged for bacteria and yeast 0 45 µm 0 45 μm ≥ 25 psig ≤ 35 cc/min @
7
2
(1 7 bar)
20 psig (1 4 bar)
Nominal lengths: • Pore size, lot and serial number are stamped on each filter 0 07 1 0 65 µm ≥ 18 psig ≤ 35 cc/min @
9 75" 10" 20" 30" 40" element for identification and traceability 0 0 0 65 μm (1 2 bar) 15 psig (1 0 bar)
24.8 25.4 50.8 76.2 101.6 cm • Complete qualification guide available 0 2 4 6 8 USGPM
Outside diameter: 2 7" (6 9 cm) 0 7 6 15 1 22 7 30 3 LPM
Inside diameter: 1 0" (2 54 cm) CERTIFICATIONS For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise TYPICAL BACTERIAL RETENTION
Surface area: 7 6 ft (0 7 m ) • USP Class VI: Meets USP Class VI Biological Test for Plastics
2
2
per 10" element 0 2 μm LRV for B diminuta ≥ 7 8
• FDA Listed Materials: All materials comply with FDA Title 21 of the Code of
Operating Parameters Federal Regulations Sections 174 5, 177 1520, and 177 2440 as applicable 0 45 μm LRV for S marcescens ≥ 8 5
Maximum sustained for food and beverage contact 0 65 μm LRV for S cerevisiae ≥ 11
operating temperature: • European Directive for Food Contact: European Regulation No 1935/2004
176°F (80°C) at 20 psid (1 38 bar) and European Regulation 10/2011: Tested for migration behavior and is
Maximum differential pressure: suitable for contact with all kinds of foodstuffs with minimal rinse-up
80 psid @ 70°F (5 5 bar @ 21°C) Data available upon request
40 psid @ 160°F (2 8 bar @ 71°C)
Maximum reverse differential pressure: TYPICAL APPLICATIONS
40 psid @ 70°F (2 8 bar @ 21°C) • Bottled Water • Reagent Chemicals • Buffers
Recommended change-out pressure:
35 psid (2 4 bar) • Ophthalmic Solutions • LVPs • Juices Customer Service/Technical Support: 1-888-353-0303
• Culture Media Europe (UK): +44-1424-777791 | China: +86-21-5238-6576 | Asia: +65-9671-9966
302-731-1700 | 800-249-1990 | Fax: 1-302-369-0938 | info@gravertech.com | www.gravertech.com

| 13 | | 14 |